Productivity 1000 Series PLC PID Instruction

PID Loop (PID) Instruction (Auto Tuning) – Productivity 1000 PLC
A Proportional-Integral-Derivative algorithm is a generic Control Loop feedback formula widely used in industrial control systems. A PID algorithm attempts to correct the Error between a measured process variable and the desired setpoint by calculating and then outputting a corrective action that can adjust the process accordingly and rapidly, to keep the Error to a minimum.
Productivity 1000 Series PLC PID Instruction
The following links will explain the PID instruction.
https://www.csimn.com/CSI_pages/PIDforDummies.html
http://www.ni.com/white-paper/3782/en/
https://en.wikipedia.org/wiki/PID_controller
We will be using an immersion heater in a cup of water to keep the temperature at a constant value. Using the Productivity Suite software we will perform an autotune on our PID instruction.
Productivity 1000 Series PLC PID Instruction
Our immersion heater will be controlled through a relay using time proportional control from our PID output. Let’s get started.

Previously in this Productivity 1000 series PLC, we have discussed:
System HardwareVideo
Installing the SoftwareVideo
Establishing CommunicationVideo
First ProgramVideo
Documenting the ProgramVideo
Monitoring and Testing the ProgramVideo
Online Editing and Debug ModeVideo
Numbering Systems and Tag DatabaseVideo
Contact and Coil InstructionsVideo
Timer InstructionsVideo
Counter InstructionsVideo
Math InstructionsVideo
Data Handling Instructions Part 1Video
Data Handling Instructions Part 2Video
Array Functions Part 1Video
Array Functions Part 2Video
Array Functions Part 3Video
Program ControlVideo
Drum Sequencer InstructionsVideo
Data LoggerVideo
Web ServerVideo
Modbus RTU Serial CommunicationVideo
Modbus TCP Ethernet CommunicationVideo
Firmware UpdateVideo
AdvancedHMI Modbus TCP Ethernet CommunicationVideo
Email and Text CommunicationVideo

Thermocouple Card (Feedback) – Productivity 1000 PLC (P1000)

We are using a P1-04THM thermocouple card to read our temperature in degrees Celsius.
Under the Setup in the main menu, select Hardware Config.
Productivity 1000 Series PLC PID Instruction
Double click on the card to call up the P1-04THM window.
Productivity 1000 Series PLC PID Instruction
Our temperature scale will be set for Degrees C. The first point input will be used with a J type thermocouple. We will leave the default User Tagname for this point as AIF32-0.1.4.1.
Productivity 1000 Series PLC PID Instruction

Wiring – Productivity 1000 PLC (P1000)

As mentioned above we will wire our J type thermocouple into the first point of our P1-04THM card. We are using an immersion heater that is rated for 125W of power using 120VAC supply. DO-0.1.2.1 will be our relay output on our P1-16CDR card that will turn on and off our heater. This relay is wired in series with the heater. See the video below for the wiring and operation of our PID instruction in the Productivity 1000 PLC.

Creating our Ladder Diagram – Productivity 1000 PLC (P1000)
PID Loop Instruction

We will create a new task called PID to run every scan under Task Management.
Under the Instructions section, select PID Loop under the PID heading.
Ladder Logic Programming Sample Code
Click on Use Structure and call it PID1.
Ladder Logic Programming Sample Code
Uncheck the Use Structure. This will keep you from having to enter all of the fields manually.
Ladder Logic Programming Sample Code
We will name the loop “Water_Heater”. Our process variable will be our thermocouple input. (AIF320.1.4.1)
Note: Our Set Point for our PID loop will be in the tag PID1.SetPoint. Most parameters required to configure a basic PID loop are located in this tab.
Click on the Major Advanced tab.
Productivity 1000 Series PLC PID Instruction
Here are all of the parameters set with tags. Common configuration parameters for more Advanced applications are located on this tab. Our process action will be left as the default forward. Click on the Major Alarms tab.
Productivity 1000 Series PLC PID Instruction
All of the limits, deviations and alarm information and bits are displayed. Hit OK.
Note: Minor tabs are only active when cascade mode is selected.
Productivity 1000 Series PLC PID Instruction
We will now set up our parameters in the Tag Database under the Structure for PID.
Our set point will be memory retentive with an initial value of 50 degrees C.
InputRangeMax is set at 100 degrees C and the InputRangeMin is set at 0 degrees C.
The Gain (P), Reset (I) and Rate (D) have been changed to a Float, 32Bit. This will allow the values to be more defined. They are also selected as memory retentive.
OutRangeMax is set for 65535. This is the maximum value for a 16-bit register. (FFFF) The OutRangeMin is set for 0. The OutUpperLimit and OutLowerLimit is set for the same values.
SampleRate is set for 500. This represents 500 ms or twice a second. Our PID loop values will be solved two times every second.
Our PID Loop instruction is just about complete.
Ladder Logic Programming Sample Code
We will add Switch 1 to enable our PID instruction. Switch 2 when off will set the instruction to manual. When switch 2 is on the instruction will be automatic.

Time Proportional Control (Relay Cycle ) – Productivity 1000 PLC (P1000)

Ladder Logic Programming Sample Code
Time-proportional control will take our PID output and energize a relay to be on in our control period at the same ratio as the PID output. Our PID loop output will be a value between 0 and 65535.
The first rung sets up a control period for our relay. In our case, we are using a 2-second timer as our control period.
Scale linear is used to scale our PID output (0 to 65535) to our control period (0-2.00 seconds)
TMR2 sets the amount of time that our relay will be ON for our control period.
Rung 4, line 5 contains the logic to turn on the relay for the proportion of the control period. PID1.Output not equal to 0 will ensure that the output will not chatter every time TMR1 resets.
Ladder Logic Programming Sample Code
Our ladder logic is now complete.

Productivity 1000 Series PLC PID Instruction

PID Tuning – Productivity 1000 PLC (P1000)

Once our program has been downloaded into the PLC, we can now tune our PID loop. Ensure that you are online with the controller and select PID Tuning under the Monitor and Debug heading in the Application Tools. Alternatively, you can use the main menu Tools | PID Tuning.
The PID loop must be enabled with our switch 1 and in manual mode (Switch 2 off) for tuning to take place.
Productivity 1000 Series PLC PID Instruction
Call up our Water_Heater loop. You will see two graphs. The first graph is for SV (set value) and PV (present value). Graph two will show the OUT of the PID loop and Bias. Bias is the percentage Value that is added to the Output to stabilize the process control.
In the picture above we have started the auto-tune process. The initial PV Bump was set to 5%. This means that the SV will be increased from 41 to 43.05 before the output will turn off. You will see the indication of the process Running.
Productivity 1000 Series PLC PID Instruction
The Ziegler-Nichol Closed Loop Tuning method is used to drive the control output fully ON to drive the Process Variable (PV) above the configured Set Point (SP) then drive the control output fully OFF until the PV drops below the SP. It repeats this method for three complete cycles to accurately calculate the new P-I-D values for your process.
Productivity 1000 Series PLC PID Instruction
When auto-tuning has been completed there will be an indication showing Complete. The PID values will now be changed.
Placing our switch 2 on will put our PID Loop instruction in auto.
Productivity 1000 Series PLC PID Instruction
We can monitor the control that we have programmed and tuned.
Productivity 1000 Series PLC PID Instruction

Download the productivity 1000 PID instruction program here.

See the video below to watch our PID instruction (Auto Tuning) in action with our Productivity 1000 PLC.

Productivity 1000 Series PLC from Automation Direct

Overview Link (Additional Information on the Unit)
Configuration (Configure and purchase a system – BOM)
User Manual and Inserts (Installation and Setup Guides)
Productivity Suite Programming Software (Free Download Link)
This software contains all of the instruction sets and help files for the Productivity Series.

Next time we will look the ramp/soak PID instruction in the Productivity 1000 Series PLC.

Watch on YouTube: Productivity 1000 Series PLC PID Instruction (Auto Tuning)


If you have any questions or need further information please contact me.
Thank you,
Garry



If you’re like most of my readers, you’re committed to learning about technology. Numbering systems used in PLC’s are not difficult to learn and understand. We will walk through the numbering systems used in PLCs. This includes Bits, Decimal, Hexadecimal, ASCII and Floating Point.

To get this free article, subscribe to my free email newsletter.


Use the information to inform other people how numbering systems work. Sign up now.

The ‘Robust Data Logging for Free’ eBook is also available as a free download. The link is included when you subscribe to ACC Automation.


6 thoughts on “Productivity 1000 Series PLC PID Instruction”

  1. Do you think you could do a cascade pid example. We deal with systems that have a slow reaction times like a heater heating up a liquid inside of a vessel or a chiller cooling liquid inside of a vessel.

    Reply
  2. How would I adapt this PID instruction for cooling instead of heating? Or be able use both heating and cooling whether the set point is above or below?

    Reply
    • Hi James,
      Under the PID instruction in the Major Advanced tab, you will see the Process Action.
      Forward: As the Output increases so will the Process Variable. (i.e., heating loop)
      Reverse: As the Output increases the Process Variable will decrease. (i.e., cooling loop)
      If you want heating and cooling, I have seen this done a couple of different ways.
      1 – Monitor the set value and when so many degrees above the set value turn on the cooling action. This would be just On/Off action for the cooling.
      2 – Set up another PID for the cooling action.

      I hope this helps you out.
      Regards,
      Garry

      Reply
  3. If all I am controlling is a cooling valve, do I need the time proportional control part of the program? Could the PID loop work without it?

    Reply
    • Hi James,
      Yes, the time proportional part of the program will control the output based on a relay (contactor) turning on and off. If you have a valve, that takes an analog input, you can eliminate the proportional part and drive the valve with the analog signal.
      Regards,
      Garry

      Reply

Leave a Comment